HWK Performance Free shipping €120+ (AT/DE)

HWK Performance

Product search

Your cart

Alpine skier on a groomed mountain piste

HWK SKIWAX · ALPINE SKI SERVICE FROM TYROL

How to prepare
alpine skis.

Check the edges. Care for the base. Choose the right wax. A practical guide to the steps and tools for your next ski day.

Edge care / hot waxing / training / race service

01

Edges first

Check the angles and look for damage. Work on the side edge only as needed and remove as little material as possible. Then start waxing.

02

Clean base

Remove all metal filings, dirt and residue. Choose a wax for the snow, intended use and product range.

03

Expose the structure

Let the wax cool, then scrape, brush and polish. The base structure should be visible and the steel edges free of wax residue.

YOUR WORKBENCH ROUTINE

Six steps for a clean ski service.

For regular maintenance, follow a consistent routine. Check new, damaged or freshly ground skis more closely first.

01

Inspect

Check the base, edges, angles and any damage. Confirm the geometry before proceeding if it is unclear.

02

Care for the edges

Expose the side edge if needed. Work at the existing target angle and smooth with a diamond stone.

03

Clean

Remove metal filings and grinding dust. Depending on the condition of the base, brush it out or clean it and allow it to dry.

04

Wax

Choose a product and apply as directed. Keep the iron moving during hot waxing.

05

Scrape and brush

Let the wax cool. Clear the edges, scrape the base with a sharp plexiglass scraper and brush out the structure.

06

Final check

Check that the edges are dry and burr-free, there are no wax deposits and the structure is visible and free of dust.

HWK brushing an alpine ski

PRECISION FIRST

Less pressure.
More care.

Clean guides, sharp tools and controlled passes matter more than the number of passes.

The base edge needs filing only occasionally. For waxing, use the temperature specified for the product. The finished base should have fully exposed structure.

THE STEPS IN DETAIL

Care for the edges and base.

Maintain and preserve the edges

The base edge, sidewall and side edge need attention at different intervals. For regular maintenance, use a diamond stone as needed and keep filing to a minimum.

  • Base edge: Check and preserve the existing angle. Work on it only when needed after grinding or repair. Avoid daily filing.
  • Sidewall: Remove just enough sidewall material for the file and diamond stone to rest fully on the steel edge. Remove the filings afterwards.
  • Side edge: Set the target angle, keep the guide clean and make a few controlled passes. If the file chatters, stop and check the cause.
  • Diamond finish: Work from coarse to fine at the same angle. Start with 2–3 light passes and check again.
  • After skiing: Dry the edges immediately and check for rust and burrs. Address small defects early and remove as little material as possible.

Check the existing base bevel before adjusting it. It is easy to increase the angle by hand and difficult to reduce it again. Ask a technician if the geometry is unclear.

Hot waxing for regular maintenance
  • Bring the skis to room temperature, clamp them securely and inspect the base.
  • Dry-brush normally clean skis. For heavy dirt or salt, use an appropriate base cleaner and allow it to dry completely.
  • Select the appropriate wax and set the iron to the temperature specified for that product.
  • Apply evenly, moving the iron steadily from tip to tail. Keep it moving and avoid smoke.
  • Let the ski cool completely. Remove wax from the steel edges and side areas first, then scrape the base with a sharp plexiglass scraper.
  • Open the structure with a suitable bronze or metal brush and finish polishing with nylon. Use metal hand brushes in the direction of travel.

Take extra care to remove grinding dust and loose microfibres from new or freshly ground bases. Use Fibertex only where needed and with light pressure. Follow any specific instructions for particularly hard waxes.

Paste and liquid wax for quick touch-ups

Paste and liquid wax are easy to apply without an iron. Apply a thin, even coat to a clean, dry base. Allow it to dry as instructed for the product, then brush or polish.

Drying times vary by product. Continue regular hot waxing on new, freshly ground, dry or heavily used bases. Keep up the underlying base care alongside the finish.

Secure the ski firmly. Wear suitable cut-resistant gloves when handling sharp edges and use eye protection and a guard with rotary tools. Use good ventilation or extraction when hot waxing.

CHOOSING YOUR WAX

The right wax for your ski day.

Regular base care and a suitable training wax are the starting point. Choose a product and application method for your skis and the current conditions.

  • Racing WAX

    Racing WAX – 180g

    Alpine
    −10 to +10 °C
    €21,00
  • Alpine Service Wax Soft

    Alpine Service Wax Soft – 180g

    Alpine
    −10 to +10 °C
    €21,00
  • LX Paste AllroundWax paste

    LX Paste Allround

    General
    −10 to +10 °C
    €30,00
  • LX Basespray AllroundLiquid wax

    LX Basespray Allround

    General
    −10 to +10 °C
    €24,00

Check the intended use. A general temperature range is separate from an alpine-specific recommendation. Follow the application instructions for the particular product.

FOR RACE TRAINING AND RACE DAY

Choose a base and finish that work together.

Start with a suitable base and follow it with a finish. Consider snow and piste type, snow temperature, moisture, piste treatment, discipline and the existing base structure. Air temperature alone is insufficient.

1 · Iron-on racing base

Choose HX Racewax Warm, Middle or Cold according to the current product guidance. A suitable UHX Powder may work as an iron-on base for speed events. For fine fresh snow, consider the corresponding Newsnow products.

  • HX Racewax WarmSki wax

    HX Racewax Warm

    Nordic
    +5 to +15 °C
    Alpine
    +5 to +15 °C
    €72,00
  • HX Racewax MiddleSki wax

    HX Racewax Middle

    Nordic
    −5 to +5 °C
    Alpine
    −5 to +5 °C
    €72,00
  • HX Racewax ColdSki wax

    HX Racewax Cold

    Nordic
    −15 to −5 °C
    Alpine
    −15 to −5 °C
    €72,00
1 · Racing base without an iron

Choose an HX Paste for the conditions. Apply, allow to dry according to the product instructions, then brush and polish. Continue periodic hot waxing when the base needs it.

  • HX Paste WarmWax paste

    HX Paste Warm

    Alpine
    0 to +15 °C
    €50,00
  • HX Paste MiddleWax paste

    HX Paste Middle

    Alpine
    −10 to 0 °C
    €50,00
  • HX Paste ColdWax paste

    HX Paste Cold

    Alpine
    −20 to −10 °C
    €50,00
2 · Match the finish to snow and moisture

Combine a liquid finish and block only where the snow conditions call for it. The brush and application method depend on the product. There is no single speed setting for the merino roller.

  • Prototype FFL 34 SprayLiquid wax

    Prototype FFL 34 Spray

    Alpine
    0 to +15 °C
    €90,00
  • UHX Liquo Spray MiddleLiquid wax

    UHX Liquo Spray Middle

    Nordic
    −5 to 0 °C
    Alpine
    −5 to 0 °C
    €90,00
  • UHX Liquo Spray ColdLiquid wax

    UHX Liquo Spray Cold

    Nordic
    −15 to −5 °C
    Alpine
    −15 to −5 °C
    €90,00

ESSENTIAL TOOLS

The right tool for each step.

A small set of tools covers the main steps. Choose the guide and tools to match the existing ski angles.

01 / SECURE THE SKI

Stable at the workbench

A solid ski vise and brake retainers hold the ski without twisting it. Prepare a stable work surface and clean cloths.

02 / EDGES

Guide the angle precisely

Use a base guide, side-edge guide, file and medium and fine diamond stones. Use a sidewall planer only if the steel edge is obstructed.

03 / WAX

Control the temperature

Use a suitable iron, wax and sharp plexiglass scraper. Follow the product instructions for temperature and application.

04 / FINISH

Brush out the structure

Use a suitable bronze or metal brush to open the structure and nylon to polish. Use merino only for the specified application steps.

BEFORE YOU HIT THE SLOPES

A final check.

  • Edges evenly sharp and dry.
  • No noticeable burrs on the base edge and no damage left unchecked.
  • Steel edges and side areas free of wax residue.
  • Structure visible, clear and dust-free.
  • Dry the skis after use and store them in a dry place.

QUESTIONS FROM THE WORKBENCH

Get ready for your next service.

Do I need to file the edges before each wax?

Inspect them each time and remove material only when needed. Use a suitable diamond stone at the existing angle for small burrs and early dulling. Avoid daily filing of the base edges.

Which edge angle suits my skis?

The angle depends on the ski, skier, intended use and existing geometry. HWK cites 0.5°, 0.7° and 1.0° for base bevels and 88° and 87° as examples for sporting and racing side edges. Keep a correct existing angle and record the choice for each pair.

How can I tell when the base is ready?

After scraping and brushing, the structure is fully visible and clear. There are no wax ridges along the steel edges. The base is clean and free of dust.

How long should the ski cool after hot waxing?

Follow the product instructions first. HWK gives about 15 minutes as a guide for initial base preparation. For regular waxing, allow the ski to cool completely. Follow any special scraping instructions for very hard waxes.

Can I use paste or liquid wax for the entire season?

Both are practical for quick applications. New, freshly ground, dry or heavily abraded bases still need suitable base preparation and periodic hot waxing.

Can I use a general temperature range for alpine skiing?

A general product range does not automatically apply to every discipline. The product cards identify any alpine-specific range. Use the latest product guidance and the alpine wax adviser.

What if the file or scraper chatters?

Stop and find the cause. With a file, look for a hardened damaged area, too much pressure or clogged teeth. Check the scraper for sharpness and the pressure you are applying.

HWK · EBBS IN TYROL

Your skis. Your conditions.

Find your wax in the alpine adviser or ask HWK for personal advice on your next ski service.